Washing Machine Drain Pump Replacement in Warsaw
Washer not draining, stopping on rinse or spin, buzzing when it should drain, or showing a drain error? The drain pump pushes water out of the drum. Its impeller can get stuck on coins, hairpins and threads — or the motor just wears out over time. We replace drain pumps on site all over Warsaw — from Wola to Wawer.
Cost
The pump itself is cheap — this is one of the most frequent washer repairs. See the table for prices. Diagnostics are included, pump billed separately.
| Service | min | max |
|---|---|---|
| Drain pump replacement (washing machine) | 250 zł | 350 zł |
| Heating element replacement (washing machine) | 250 zł | 320 zł |
| Water inlet valve replacement (washing machine) | 250 zł | 300 zł |
| Shock absorber replacement (washing machine) | 300 zł | 400 zł |
| Belt replacement (washing machine) | 250 zł | 300 zł |
| Bearing replacement (washing machine) | 550 zł | 660 zł |
| Door lock replacement (washing machine) | 250 zł | 300 zł |
| Control module repair (washing machine) | 400 zł | 550 zł |
How it works
- You tell us the symptom — not draining, buzzing, error code.
- The technician identifies the model.
- We disconnect it from power and water.
- Residual water is drained through the filter.
- The filter is checked — if it’s clean but the pump is dead, it needs replacement.
- We remove the lower panel or lay the machine on its side to reach it.
- Hoses and plug are disconnected, a new pump is fitted. Then we test — quick, quiet draining.
Mistakes
- Skipping the filter check first — 30% of cases turn out to be a clogged filter, not the pump.
- Mixing up a bent hose with pump failure.
- Ordering a pump with the wrong connector.
- Keeping on washing without drainage — water stays inside, then smell and mould start.
- Not inspecting the impeller for debris — a coin may jam it even when the pump itself still works.
Preparation
- Washer model.
- Describe the issue: not draining, error, buzzing.
- Unplug it and shut off the water.
- Towels — a lot of water comes out when draining the filter.
- A basin under the filter.
- Access from the front and underneath.
- A photo of the model.
- Installed under a countertop? Tell us in advance.
Case from Warsaw
Client in Wola: Bosch — stopping on spin with error E18. Filter was clean, hose was clear. The pump impeller was stiff — a 50-grosz coin had jammed between the impeller and housing. We removed the coin, but the motor was already damaged (winding overheated). Replaced the pump. Test — drained in 30 seconds, quietly. 40 minutes. Tip: always check pockets before washing — coins, pins and buttons are the #1 pump killers.
FAQ
What is the drain pump for?
It pumps water from the drum into the drain after the wash and rinse cycles.
How can I tell it has failed?
No draining, error code, buzzing while draining, water left in the drum.
Could it be something else?
A blocked filter (30%), a kinked hose, or a blocked drain pipe.
Can I check the filter myself?
Open the hatch at the bottom front, put down a basin, and unscrew the filter cap.
Do you bring the pump?
Yes.
How long does it take?
30–60 min.
Which brands?
Bosch, Samsung, LG, Electrolux, Beko, Whirlpool, Indesit, Gorenje.
Is it expensive?
No — one of the cheapest parts in a washer.
Can I wash if it won’t drain?
No — standing water leads to mould and bad smell.
Who does the work
Drain pump replacement done by washer repair specialists. We cover all of Warsaw. Not draining? Call us — fixed in 30 minutes.