Kitchen Wall Panel Installation in Warsaw — Backsplash Above Countertop
A wall panel between the countertop and upper cabinets does more than look good — it shields the wall from water splashes, grease, and steam. Without a backsplash, plaster or paint starts wearing out fast, especially by the sink and hob. Fitting the panel takes a few hours, but the work has to be exact — cutouts for sockets, lining up corner pieces, and pressing the panel evenly to the wall. We work all over Warsaw and come with our own tools and fixings.
How much does it cost and what affects the price
The price of wall panel fitting depends on the kitchen length, the panel material, and how many cutouts are needed. Laminate and MDF panels go in faster; glass panels need a more careful approach. Cutouts for sockets and switches are charged separately — each one increases the final amount. Fixings (adhesive, screws, decorative caps) are part of the labour cost. The panel itself is bought by the client. Up-to-date rates for all kitchen services are in the table below.
| Service | min | max |
|---|---|---|
| Kitchen furniture installation (complete set) | 20% od ceny | 25% od ceny |
| Kitchen base cabinet installation | 250 zł | 400 zł |
| Wall cabinet installation | 250 zł | 400 zł |
| Kitchen cabinet door adjustment | 80 zł | 150 zł |
| Hinge replacement | 60 zł/szt | 120 zł/szt |
| Kitchen countertop installation | 200 zł/mb | 350 zł/mb |
| Laminate countertop installation | 150 zł/mb | 250 zł/mb |
| Composite countertop installation | 250 zł/mb | 400 zł/mb |
| Countertop joining | 190 zł/szt | 300 zł/szt |
| Countertop cutout (sink / hob) | 120 zł/szt | 200 zł/szt |
How the on-site work goes
- You send a kitchen photo and the wall dimensions — the technician checks the scope of work.
- We set a date and time — often for the same day or the next day.
- The technician measures the wall to the millimetre, marking sockets, pipes, and uneven areas.
- The panel is marked out and cut on site — with a jigsaw or circular saw.
- Openings for sockets are cut using hole saws or a router.
- The panel is attached with adhesive (mounting glue) or screws — depending on the wall and the panel material.
- Joints are covered with skirting strips or decorative profiles, and the final fit is checked.
Common customer mistakes (and how to avoid them)
- Buying a panel without precise measurements — it ends up too short in length or height, so another piece has to be bought.
- Ignoring panel thickness when ordering the kitchen — the upper cabinets no longer sit flush to the wall.
- Trying to glue a panel onto a crooked wall — gaps appear and the panel bends.
- Overlooking sockets — once the panel is in place, access is blocked and the work has to be redone.
- Picking a PVC panel next to a gas hob — the plastic deforms from high heat.
- Cutting the panel with an angle grinder and no guide — the laminated surface chips.
- Not leaving room for thermal expansion — the panel warps in summer.
What to prepare before the technician arrives
- Buy the panel in the right size — the technician can suggest a material, but the purchase is on your side.
- Make sure the countertop is already fitted — the panel is installed after that.
- The upper cabinets should already be mounted or at least marked out — this sets the panel height.
- Clear the countertop of dishes, appliances, and small items.
- Check where the electrical wiring runs inside the wall — so a screw does not hit a cable.
- If sockets need moving — get that done before the panel is fitted.
- Have a power socket available for tools (jigsaw, drill/driver).
- Provide access to the apartment: intercom code, parking info.
- If the wall is badly uneven — tell us beforehand, as levelling may be required.
A real case from Warsaw
A client in the Praga-Południe district ordered fitting of a laminate panel in a 3.2-metre kitchen. The kitchen was L-shaped, with four sockets in the backsplash zone and a gas hob. During measuring, we found the wall was out by 8 mm — shims had to go behind the panel so it would sit tight. All four socket openings were cut with a 68 mm hole saw with allowance. The panel was fixed with mounting adhesive, and the joint with the countertop was finished with an aluminium skirting strip. A heat-resistant insert was added next to the hob. The whole job took around 3 hours. The client was happy — the wall is fully covered and the seams between panels are barely visible (compatible with IKEA, Nobilia, BRW and similar).
Frequently asked questions
Which panel material is best for a kitchen?
Laminated MDF gives the best mix of price and everyday practicality. Glass costs more but is easier to wipe clean. PVC is a cheaper option, but it should not be used near a hob.
Can a panel be installed without upper cabinets?
Yes — in that case the top edge is finished with a decorative profile, or the panel runs all the way up to the ceiling.
Do old tiles need to be removed before panel installation?
Not always. If the tiles are solid, well attached, and even, the panel can be mounted straight over them.
What’s included in the labour cost?
Measuring, cutting the panel, making socket cutouts, installation, and fitting skirting strips. Fixings are included. The panel itself and decorative elements are charged separately.
How long does installation take?
A standard 2–3 metre kitchen takes 2 to 4 hours, depending on the number of cutouts and the condition of the wall.
Can the panel be replaced without removing the cabinets?
In most cases — yes. The technician carefully removes the old panel and fits the new one, matching it to the existing cabinets.
Do you work with glass panels (splashbacks)?
Yes, but glass panels have to be made to measure in advance — they cannot be cut on site.
Who does the work
Kitchen panel fitting is done by technicians with hands-on experience in kitchen furniture installation and finishing work. We cover all of Warsaw and nearby suburbs. Minimum order — from 200 zł. To book, call or message us — we answer within an hour and will tell you what to get ready beforehand.