VIYAR Furniture for a Restaurant in Warsaw — a Custom Fit-Out Case Study

A restaurant in Warsaw needed a full custom fit-out: wall panelling, built-in banquettes and lit niches, all in warm walnut. We built it from VIYAR laminated board — cut to size, assembled and mounted on site, fitted to concrete walls that were anything but straight. Here is how the project went, what drives the cost of work like this, and what to plan for if you are fitting out a café or restaurant.

How much a custom furniture fit-out costs — and what drives the price

The price of a project like this depends on the number of elements, the type of board and finish, how much cutting and edge-banding is involved, and how much on-site fitting the space demands. Panelling over uneven concrete takes far more scribing and adjustment than a free-standing cabinet. We quote each job up front and you pay after the work is done — materials (board, edging, fittings) are billed separately. Current rates for the individual furniture services are in the table below.

Service	min	max
IKEA furniture assembly	20% of price	25% of price
Freestanding wardrobe assembly	250 zł	450 zł
Built-in wardrobe installation	400 zł	800 zł
Chest of drawers assembly	180 zł	300 zł
Bed assembly	200 zł	350 zł
Table / desk assembly	180 zł	300 zł
Chair assembly	40 zł/pc	80 zł/pc
Furniture disassembly	100 zł	250 zł
Furniture rearrangement in apartment	120 zł/h	200 zł/h
Furniture repair	150 zł	350 zł
Hinge adjustment	60 zł/pc	120 zł/pc
Hinge replacement	60 zł/pc	120 zł/pc
Drawer slides replacement	80 zł/pc	180 zł/pc
Furniture modification	150 zł	400 zł
Furniture shortening	120 zł	300 zł
Furniture fitting to alcove	250 zł	600 zł
Shelf installation	80 zł	150 zł
Coat hanger installation	60 zł	120 zł

How the project went, step by step

1. Measuring the space — walls, niches and floor levels in several points, because concrete is rarely truly square.
2. Cutting the VIYAR board to size and edge-banding every visible edge.
3. Assembling the carcasses and the perforated decorative panels away from the wall.
4. Mounting the wall panelling and aligning it to the real wall, scribing where needed.
5. Building in the banquette bases and fitting the leather seat cushions and bolsters.
6. Integrating the LED strips and power sockets into the niches, then a final fit and adjustment.

Working with VIYAR board: what matters (and where it usually goes wrong)

• Measuring “by eye” with no allowance — a panel comes out short and the whole sheet is wasted.
• Cutting laminated board without taping the line — the decor chips along the edge.
• Leaving cut MDF edges unbanded in a humid kitchen zone — the board swells over time.
• Mounting panelling tight to concrete without scribing — gaps open up where the wall bows.
• Matching the walnut decor across different board batches — the shade can drift.
• Planning niches without fixing the LED and socket positions first — you end up cutting finished panels.

What to prepare for a furniture project in a café or restaurant

• A clear, agreed layout — where panelling, benches and niches go.
• Final decisions on the board decor and the leather or upholstery colour.
• Coordinated electrics — socket and LED positions marked before panels go up.
• Access and a power point on site, plus room to cut and assemble.
• Realistic site readiness — walls plastered, floor down, so furniture meets finished surfaces.
• A schedule that fits the venue — most fit-out work is done before opening or off-hours.
• Agreement on who supplies the board and edging (we can source VIYAR or work with yours).
• Protection for finished floors and surfaces during the dust-making stages.

The result: the restaurant interior

The finished room reads as one warm, continuous piece: full-height walnut panelling, a perforated panel that doubles as a design feature, and a deep alcove with built-in seating. The cognac leather banquettes sit against raw concrete, while the lit niches give the bar area a soft, hospitable glow.

Every element was cut and fitted to the actual space, not to a catalogue size — which is why the panels meet the concrete cleanly and the seating runs flush along the wall. For a venue in central Warsaw, that level of fit is what separates a custom fit-out from flat-pack.

The whole installation was planned around the venue’s schedule, so the dusty work happened before the dining room was in use.

Frequently asked questions

Do you work with VIYAR board?

Yes — we cut, edge-band and assemble VIYAR laminated board, and we can either source it or work with the board you supply.

Can you build furniture for a restaurant or café?

Yes. We do full custom fit-outs — wall panelling, built-in banquettes, bar and service furniture, lit niches — built and mounted on site.

Do you cut and assemble on site?

Simple cutting and fitting we do on site. For a large cut list we sometimes pre-cut the panels and only fit and adjust on location.

How do you handle uneven concrete walls?

We scribe the panels to the real wall and adjust on site, so the panelling sits flush without visible gaps.

Can you integrate lighting and sockets?

Yes, we build LED strips and sockets into the niches; the electrical connection is done together with an electrician.

Who supplies the materials?

Either side can. We can source VIYAR board, edging and fittings, or work with what you have already bought — materials are billed separately.

Can you work around our opening hours?

Yes. Fit-out work is usually scheduled before opening or during off-hours so it does not disrupt service.

Do you cover the whole of Warsaw?

Yes — the whole city and surroundings: Śródmieście, Mokotów, Wola, Praga and beyond.

Who did the work and how we work

The fit-out was done by experienced HandyMan24 craftsmen who assemble and fit furniture across Warsaw every day. We measure first, quote up front, work clean with dust extraction, and you pay after the job — no deposits.

Planning a fit-out for your venue, or a custom piece for your home? Leave a request online — we’ll come, measure and build it to your space.