Important: before any dryer repair, disconnect the appliance from the power. Internal heating parts can stay very hot even after the machine has been turned off. Do not try to take it apart yourself — their technician works only on equipment with no power connected.
How much does tumble dryer repair cost
Up-to-date prices are listed in the table below. The final amount depends on the brand, the dryer type (condenser, heat pump, vented), and the fault itself. Diagnostics are part of the repair price. Spare parts are billed separately.
| Service | Price |
|---|---|
| Belt replacement (dryer) | 300–450 zł |
| Rollers / bearings replacement (dryer) | 350–500 zł |
| Heating element replacement (dryer) | 300–450 zł |
| Fan replacement (dryer) | 300–400 zł |
| Condensate pump replacement (dryer) | 300–400 zł |
| Control module repair (dryer) | 300–600 zł |
Indicative prices. Ranges for a typical scope. Fixings included, materials separate. Minimum order 300 zł.
What it costs and how to book: home repair service in Warsaw.
How the home repair works
- You explain the issue: laundry stays damp, there is no heat, or an error appears on the display.
- The technician checks the model and brand, and asks you to send a photo of the data plate.
- Timing depends on the tradesperson you choose: they give the arrival time in their offer.
- At your home, the technician disconnects the machine from power and starts diagnostics.
- Finds the cause: heating element, thermostat, condensate pump, filter, humidity sensor, control board.
- If the part is available, repair is done right away. If not — they order it and schedule a return visit.
- Runs a test drying cycle, checks the temperature and every programme mode.
Common tumble dryer owner mistakes
- Skipping lint filter cleaning after each cycle, airflow gets restricted, the machine overheats and the thermal cut-out trips.
- Neglecting the condenser (heat exchanger): it should be rinsed once a month, otherwise drying performance falls off.
- Stuffing the drum too full — clothes stay wet, the cycle runs longer, and the heating element works at full strain.
- Drying items with large hardware (zips, buttons) without a laundry bag, they hit the drum and the door glass.
- Setting the machine tight against the wall: there is no ventilation, and condensate cannot drain properly.
- Ignoring the error code and carrying on with drying — this makes the problem worse.
What to prepare before the technician arrives
- Write down the error code shown on the display (if any).
- Take a photo of the data plate with the model and serial number.
- Disconnect the machine from the socket.
- Take the laundry out of the drum.
- Clean the lint filter, and show it to the technician.
- Empty the condensate container (if applicable).
- Make space for access: pull the machine out from the wall.
- Note when the problem began and which programme was running at the time.
- Confirm the dryer type: condenser, heat pump, or vented.
- Share access details: intercom code, parking info.
A real case from Warsaw: tumble dryer repair
A client in Bemowo posted a request about a Bosch heat-pump dryer that had stopped drying clothes properly — the laundry was still damp even after a full cycle. No error code showed up. Diagnostics found that the heat exchanger was fully packed with lint, the owner had been cleaning only the main filter and skipping the condenser. After flushing the heat exchanger and checking the humidity sensor (which was working properly), the dryer went back to normal drying times. The whole repair took 40 minutes. Lesson here: do not skip the monthly condenser clean, it is the main reason dryer performance starts to drop.
Frequently asked questions
Which dryer brands do tradespeople repair?
Bosch, Miele, Samsung, Siemens, Electrolux, AEG, Beko, Whirlpool and others.
Is the diagnostic fee separate?
Diagnostics are included in the repair price. If you decide not to proceed, you pay only for the call-out.
How long does the repair take?
Most problems are repaired in 1–2 hours. Uncommon parts mean a return visit is needed.
Why do clothes stay damp after drying?
A blocked filter or condenser, a faulty heating element, humidity sensor failure, or an overloaded drum.
What’s the difference between a condenser dryer and a heat pump dryer?
A heat pump dryer uses less electricity and dries at a lower temperature — easier on fabrics. A condenser dryer has a simpler design and is cheaper to repair.
Is it worth repairing an old dryer?
If the repair goes above 50% of a new machine’s price, the technician will advise replacement.
Do tradespeople bring spare parts?
Common ones: heating elements, thermostats, condensate pumps, belts: are often in stock.
Can I stack the dryer on a washing machine?
Yes, with a proper stacking kit. Never simply set it on top — vibration can shake it off.
How quickly can a tradesperson come?
That depends on who is free: you see the arrival time in the offer before you accept it. If it can’t wait, mark the job as urgent in the app. Tradespeople usually charge extra for urgent call-outs.
Who does the work
Tumble dryer repairs are done by technicians with hands-on experience in household appliance service. Post a request in the HandyMan24 app: tradespeople across Warsaw will figure out the issue, and you agree a time with the one you choose.
Order in the app
Describe the job, add photos and the address. Tradespeople send their own prices and dates, and you pick one of the offers.
Open the app
